# Enterprise Architect License Manager

# Introduction

Open iT supports Enterprise Architect usage reporting by collecting log files and converting them to Open iT format. This will produce the following aggregated data types used for historical reporting:

(89) Total License Use Licenseevents
(90) Individual License Use Licenseevents
(91) Usergroup License Use Licenseevents
(108) Host License Use Licenseevents
(109) Hostgroup License Use Licenseevents
(104) License Logfile Events v2.0
(107) Denied License Use Licenseevents

The following sections will guide you in setting up the necessary configuration to collect and send the required data to the server.

Apply the configurations shown in the Open iT client.

# Requirements

An Open iT Client connected to an Open iT Server or a coexistent Open iT setup
License server administrative rights
Full path to the debug log file

# Configuring Log File Collection

These are the required steps to configure collection of Enterprise Architect log files.

Go to the Components directory, which is by default in C:\Program Files\OpeniT\Core\Configuration\Components, and back up the logfilecollector-ea.xml file.
Open a command prompt with Administrator level privileges.
Go to the bin directory, which is by default in C:\Program Files\OpeniT\Core\bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd C:\Program Files\OpeniT\Core\bin
```

Once in the directory, set the location of the Enterprise Architect log files, run the command:

Command Syntax
 openit_confinit -c "logfilecollector-ea.logfilecollector.source.dir=<ea_log_dir>"

where <ea_log_dir> is the location of the Enterprise Architect log files.

Example
 openit_confinit -c "logfilecollector-ea.logfilecollector.source.dir=C:\Program Files\Sparx Systems\Keystore\Service\Logs"

Update the configuration file, run the command:
Command Syntax
```
 openit_confbuilder --client
```
Make sure that there are no errors encountered.

Refer to the Enterprise Architect Log File Collection Configuration table to learn more about Enterprise Architect configuration in logfilecollector-ea.xml.

Object Name	Accepted Value	Description
source.dir	DirName (e.g., `C:\Program Files (x86)\Sparx Systems\Keystore\Service\Logs`)	Location of the Enterprise Architect log files.
source.pattern	String (i.e., `*.log`)	The glob pattern identifying source files in the source directory.
source.seen	String (`collect`, `ignore`, or `tail`)	Seen files are the previously collected source files. `collect` - Specify this option to collect from the start each time. `ignore` - Specify this option to skip collecting from the same file again. `tail` - Specify this option to continue collection from the end of the file last time (i.e., collect the ones added since last time).
source.cmplines	Integer (e.g., `6`, `10`, `20`)	This is required if the value of `source.seen` is `tail`. This is the number of lines compared to source files collected before to determine where to start the collection. Note: If this number is too low, you can end up with an incorrect position, and duplicate data may be in the log files. Usually, it is better to have a few lines more than strictly necessary than even a single line too little.
target.dir	DirName (i,e., `${OpeniT.directories.temp}/LogFileCollector`)	This is the location of the directory containing the collected log data.
target.module	String (i.e., `license`)	The target type of module (in general).
target.datatype	String (i.e., `ea`)	The specific type of target data.
target.interval	Timespan (e.g., `P30S`, `P5M`, `P1D`)	The span of time between collector runs.
target.rotation-size	Integer (e.g., `6`, `10`, `20`)	The log file rotates if it goes beyond the number (in mb) defined.
target.rotation-glob	String (e.g., `*`)	The glob pattern to match before the log file rotates.

Enterprise Architect Log File Collection Configuration

Go to the Components directory, which is by default in /var/opt/openit/etc/Components, and back up the logfilecollector-ea.xml file.
Go to the bin directory, which is by default in /opt/openit/bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd /opt/openit/bin
```

Once in the directory, set the location of the Enterprise Architect log files, run the command:

Command Syntax
 ./openit_confinit -r /var/opt/openit/ -d /var/opt/openit/etc/ -c "logfilecollector-ea.logfilecollector.source.dir=<ea_log_dir>"

where <ea_log_dir> is the location of the Enterprise Architect log files.

Example
 ./openit_confinit -r /var/opt/openit/ -d /var/opt/openit/etc/ -c "logfilecollector-ea.logfilecollector.source.dir=/root/ea/logs"

Update the configuration file, run the command:
Command Syntax
```
 ./openit_confbuilder --client
```
Make sure that there are no errors encountered.

Refer to the Enterprise Architect Log File Collection Configuration table to learn more about Enterprise Architect configuration in logfilecollector-ea.xml.

Object Name	Accepted Value	Description
source.dir	DirName (e.g., `/root/ea/logs`)	Location of the Enterprise Architect log files.
source.pattern	String (i.e., `*.log`)	The glob pattern identifying source files in the source directory.
source.seen	String (`collect`, `ignore`, or `tail`)	Seen files are the previously collected source files. `collect` - Specify this option to collect from the start each time. `ignore` - Specify this option to skip collecting from the same file again. `tail` - Specify this option to continue collection from the end of the file last time (i.e., collect the ones added since last time).
source.cmplines	Integer (e.g., `6`, `10`, `20`)	This is required if the value of `source.seen` is `tail`. This is the number of lines compared to source files collected before to determine where to start the collection. Note: If this number is too low, you can end up with an incorrect position, and duplicate data may be in the log files. Usually, it is better to have a few lines more than strictly necessary than even a single line too little.
target.dir	DirName (i.e., `${OpeniT.directories.temp}/LogFileCollector`)	This is the directory location containing the collected log data.
target.module	String (i.e., `license`)	The target type of module (in general).
target.datatype	String (i.e., `ea`)	The specific type of target data.
target.interval	Timespan (e.g., `P30S`, `P5M`, `P1D`)	The span of time between collector runs.
target.rotation-size	Integer (e.g., `6`, `10`, `20`)	The log file rotates if it goes beyond the number (in mb) defined.
target.rotation-glob	String (e.g., `*`)	The glob pattern to match before the log file rotates.

Enterprise Architect Log File Collection Configuration

# Activating Log Data Collection

These are the required steps to activate the collection of Enterprise Architect log data.

Open a command prompt with Administrator level privileges.
Go to the bin directory, which is by default in C:\Program Files\OpeniT\Core\bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd C:\Program Files\OpeniT\Core\bin
```

Once in the directory, activate the collection of Enterprise Architect log data, run the command:

Command Syntax
 openit_oconfinit --update "C:/Program Files/OpeniT/Core/Configuration/scheduler/collect_license_ea-logs.root.scheduler.jobs.collect_ea_licenselogs.general.active=true

The collection runs every 5 minutes by default, which triggers the data collection process. To configure the intervals, locate the instances attribute under collect_ea_licenselogs, preprocess_ea_licenselogs-records, or transfer_ea_licenselogs in the same file and configure the attributes.

Refer to the Enterprise Architect Log Job Scheduler Instances Configuration table to learn the attributes used to configure Enterprise Architect data collection and transfer.

Attribute Name	Accepted Value	Description
max-instances	Uint (e.g., `5`, `8`, `9`)	The number of instances allowed to run at the same time.
max-handling	String (`end-oldest`, `end-all-old`, or `end-new`)	The action done upon reaching the maximum number of instances: `end-oldest` - Specify this option to stop/kill the oldest instance and start a new one. `end-all-old` - Specify this option to stop/kill all running instances before starting the new one. `end-new` - Specify this option to prevent a new instance from starting.
end-timeout	Timespan (e.g., `P30S`, `P5M`, `P1H`)	The maximum waiting time before terminating a running instance.
quarantine	Timespan (e.g., `P30S`, `P5M`, `P1H`)	The waiting time before starting a new instance after a previous one.

Enterprise Architect Log Job Scheduler Instances Configuration

Go to the bin directory, which is by default in /opt/openit/bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd /opt/openit/bin
```

Once in the directory, activate the collection of Enterprise Architect log data, run the command:

Command Syntax
 ./openit_oconfinit --update "/var/opt/openit/etc/scheduler/collect_license_ea-logs.root.scheduler.jobs.collect_ea_licenselogs.general.active=true

Refer to the Enterprise Architect Log Job Scheduler Instances Configuration table to learn the attributes used to configure Enterprise Architect data collection and transfer.

Attribute Name	Accepted Value	Description
max-instances	Uint (e.g., `5`, `8`, `9`)	The number of instances allowed to run at the same time.
max-handling	String (`end-oldest`, `end-all-old`, or `end-new`)	The action done upon reaching the maximum number of instances: `end-oldest` - Specify this option to stop/kill the oldest instance and start a new one. `end-all-old` - Specify this option to stop/kill all running instances before starting the new one. `end-new` - Specify this option to prevent a new instance from starting.
end-timeout	Timespan (e.g., `P30S`, `P5M`, `P1H`)	The maximum waiting time before terminating a running instance.
quarantine	Timespan (e.g., `P30S`, `P5M`, `P1H`)	The waiting time before starting a new instance after a previous one.

Enterprise Architect Log Job Scheduler Instances Configuration

# Verifying Log Data Collection

After configuration, you can verify that the data is collected by following these steps:

Open a command prompt with Administrator level privileges.
Go to the bin directory, which is by default in C:\Program Files\OpeniT\Core\bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd C:\Program Files\OpeniT\Core\bin
```

Run the command:

Command Syntax
 openit_logfilecollector -c "C:\Program Files\OpeniT\Core\Configuration\logfilecollector-ea.conf"

Verify that there are *.data files created in the LogFileCollector directory, which is by default in C:\Program Files\OpeniT\Core\Log\temp\LogFileCollector.

Go to the bin directory, which is by default in /opt/openit/bin, run the command:
Command Syntax
```
 cd $BIN_DIR
```
Example
```
 cd /opt/openit/bin
```

Run the command:

Command Syntax
 ./openit_logfilecollector -c "/var/opt/openit/etc/logfilecollector-ea.conf"

Verify that there are *.data files created in the LogFileCollector directory, which is by default in C:\Program Files\OpeniT\Core\Log\temp\LogFileCollector.

# Next Steps?

Renaming Vendor License Renaming Features Create and Add Report License Monitor